A broken switch is an unpleasant situation that requires a speedy solution. In order not to wait for the arrival of an electrician and quickly restore lighting, it is advisable to be able to repair the device yourself. Agree, this is not only convenient, but also practical from a financial point of view.
The design of the device is not particularly complicated, so the repair is available to almost any home craftsman who has at least a little experience with electrician. First you need to figure out how to disassemble the light switch, and then determine the cause of the breakdown and eliminate it.
We offer you to understand what are the features of dismantling keyboard, rotary and touch models, as well as find out the most probable reasons for the failure of the switching device.
How to get started
If the light does not turn on when the key is pressed, the breaker is not always the cause of the breakdown, do not immediately start disassembling it. First, it does not hurt to check the presence of voltage in the network, as well as the condition of the incandescent lamp. If there is no voltage, most likely the switch is in order.
It is necessary to find out what is wrong with the network (short circuit, turning off the light, damage to the power cable, etc.), and eliminate this breakdown. With a burnt out bulb it is still simpler - it needs to be replaced. If the mains and the lamp are in order, it's time to take a closer look at the switch.
First you need to find on the switchboard the machine through which this particular switch is connected, and put the levers in the “down” position, i.e. disable it. After that, check with the tester the presence / absence of voltage at the output.
The procedure is simple and does not take much time, you should not neglect it, even if there is full confidence that the device is accurately disconnected from the mains.
You can make an assumption about the nature of the breakdown even before the start of the repair. A common problem is the oxidation of contacts inside the device. If the switch does not work only occasionally, most likely the reason is precisely in the bad contacts, which will simply have to be cleaned.
In addition to the “shell” of oxidation, carbon deposits can also accumulate on the metal plate of the switch. It can also be cleaned from accumulations in order to restore the operation of the device.
Serious damage can result from improper installation of the circuit breaker. By inexperience, some amateur masters connect to the machine not a phase, but a zero core. As a result, the switch seems to work, but all the lighting wiring connected in this way remains energized.
It happens that a simple replacement of a blown bulb in such a network can turn into an electric shock. It is enough to correct the scheme so that everything works correctly.
Before disassembling the circuit breaker, you must disconnect either a separate line that supplies power to the device or the entire apartment
Similar installation errors can lead to the fact that after disconnecting the machine, the line will still remain energized. This is one of the reasons why you should always check even a disconnected device.
If there is voltage, you need to de-energize the apartment or house. If sparks appear inside the switch each time the switch is turned on and off, this usually indicates that the contacts of the device are of poor quality.
In some cases, it is necessary to replace the entire switch with the same, only a new one. Usually, the exact same model is selected for replacement, which is suitable for both the socket and the interior.
If for some reason you need to install a different model, you should make sure that the existing opening is suitable for it. Otherwise, you will have to reinstall the new socket.
The cause of frequent voltage drops in the network can be not only the general condition of the power supply network, but also a large number of powerful electrical appliances that are connected at the same time. On this occasion, you can consult with an experienced electrician, you may need to make adjustments to the existing circuit.
How to disassemble the switch
Before disassembling and repairing the circuit breaker, you need to stock up with the necessary tools: a screwdriver with an indicator or a multimeter, insulation tape, sandpaper, a straight and cross screwdriver, marker, pliers, etc.
Also, some kind of container for storing small items, for example, fasteners, will not hurt.
After disassembling the circuit breaker, remember the color coding of the wires and their connection diagram. Detailed shots can be of great help.
Another useful item when doing such work is a camera or a mobile phone with a camera. The entire process is recommended to be removed. Detailed shots can be especially useful for beginners during reassembly.
The order of work largely depends on the type of light switch.
Removing keyboard devices
Step 1. Disassembling a one-, two- or three-key switch begins with the disconnection of the keys. Usually, each of them needs to be pry off with a screwdriver or other similar device and simply removed. Some manufacturers make small protrusions or recesses on the keys to facilitate dismantling.
Step 2. Carefully remove the decorative frame. To do this, push the latches that hold it. Now the front of the switch mechanism is available for inspection.
When disassembling a switch with two or three keys, it is necessary to mark the connection point of the supply wire and remember the color of this wire, or mark the corresponding core with a marker
Step 3. It is recommended that you arm yourself with a tester and make sure that there is no power at the switch terminals. If work is carried out with a multi-key device, experienced craftsmen recommend marking with a marker a power wire common to all keys.
Step 4. It is necessary to remove the fastening latches or unscrew the bolts that hold the switch mechanism in the socket. Now you can take on a more detailed inspection and repair of the device.
Old keyboard switches are arranged somewhat differently. On the case of such devices, in front or on one of the side panels, there is a mounting bolt, which you need to unscrew. Then you can remove the entire body of the product.
For old and new switches, different types of socket outlets are used. This point should be considered if you plan to update the device.
On the keys and decorative frames of the switches, usually there are small protrusions that allow you to pry the element with a flat screwdriver and quickly remove it without damage (+)
Sometimes a too rigid mount interferes with the installation of the keys, then the bolts need to be loosened a bit, this usually helps. During disassembly of the switch, it is not always necessary to remove the key, if it does not interfere with the necessary repairs.
In this case, it is enough to detach only the frame. Spacers can be loosened to the side.
Strip the ends of the wire and fasten in the terminals. To make sure that the work is done correctly, you need to twitch the wires slightly after fixing. Any mechanical defects or damage to the cable is a good reason to replace it.
Places where there is damage to the insulation layer should be re-insulated. But if there are too many such sections, it is better to replace the cable completely, otherwise soon the switch will have to be repaired again.
Upon completion of the repair, the circuit breaker must be correctly connected to the wiring again, observing the diagram and avoiding errors that were made earlier. If wiring has been replaced, unused ground wires must be insulated.
Then you should again lock the switch mechanism in the socket and tighten the mounting bolts. Then, the keys and the decorative frame are returned.
Do not over tighten the mounting bolts during reassembly; this can change the position of the device and make installation of the key difficult
Now you need to check the operation of the switch. To do this, it is turned on and off several times. For two- and three-key devices, each key is checked separately and all at the same time. If the device does not spark, and the lamp light does not flicker, the work can be considered successful.
Our site has a block of articles with a detailed description of connecting one-, two- and three-key switches, we recommend that you read:
- Wiring diagram for the two-key switch and step-by-step installation instructions
- How to choose and correctly connect a three-key switch
- How to connect a switch with one key: rules and connection diagrams
What to do with the rotary switch
Key switches are the most common and simple models. With other variants of such devices, some difficulties may arise. Sometimes you have to fix problems with the so-called rotary switches, which are also called dimmers.
Disassembly of the rotary switch begins with the removal of the round knob. You just need to pull it forward while holding the device body
Such devices are also sensitive to power surges and short circuits, as well as their “brothers” with keys. Very often a triac breaks in dimmers. This item cannot be repaired, but it can be replaced. To start disassembling the rotary switch, you need to remove the adjustment knob.
It is mounted on semicircular elements such as “father-mother” or special slots. It is necessary to hold the switch case with one hand, and with the other, gently, but with effort, pull the handle towards you. You do not need to twist it.
Under the handle there is a fixing lock nut, it also needs to be unscrewed. Sometimes fixing is done with a screw.
After the dimmer locknut or the fixing screw is unscrewed, you can remove the device housing and gain access to its internal part
Unscrew any of these elements counterclockwise. Now you need to remove the plastic overlay, as well as the frame, if necessary. Then we should loosen the elements that hold the dimmer mechanism inside and can be removed from the socket.
First you need to check all the contacts, connections and wires, clean the resulting deposits and oxidation, restore the damaged insulation, replace the broken wires, etc.
If the triac switch triac breaks down, it must be replaced with another serviceable element with exactly the same dimensions and characteristics
The damaged triac must be removed and taken to the electrics store to find a new one, exactly the same. The assembly of the repaired device is performed in the reverse order.
As in the case with the key switch, before disassembling, you must disconnect the line, check the contacts with a tester and fix the process in the form of a photo, so as not to confuse anything during assembly.
Features of repair of touch models
Everything becomes a little more complicated when it comes to touch switches, which are turned on not by pressing a key or turning a knob, but by touch.
Such models are usually equipped with a radio remote control, they have not only electromechanical filling, but also boards with microcircuits that provide control of the device.
To disconnect the front panel of the touch switch, you can use a regular straight screwdriver, but be careful not to damage the element
To repair such a complex device, the skills of a beginner electrician may not be enough. To eliminate complex failures, you will have to invite a master who knows not only electrical engineering, but also electronics.
High-quality touch switches rarely break, but if this happens, you first need to study the manufacturer's instructions to disassemble the touch switch correctly.
First you need to remove the glass decorative plate. Under it there is a panel with one or more sensors, depending on how many lines (one, two or three) this particular model serves.
Typically, the location of the sensors is indicated by circles, as shown on the decorative panel, the area sensitive to touch.
Under the decorative cover of the touch switch is a panel with sensitive elements and control boards. Under this panel are the connectors to which the wires are connected.
Under the decorative panel there are LEDs that indicate the status of the switch: red - on, blue - off. Under the panel with sensors and boards there is a switch mechanism to which wires are connected.
Dealing with inputs and outputs is fairly simple, much the same as for a regular key switch. The sensor plate is attached to this part with clips. To remove it, you just need to disconnect them.
The main part of the switch, which is installed in the socket, usually does not have any clamps. As fasteners, ordinary bolts are used. To inspect the connection points of the wires, you need to unscrew these bolts and remove the switch from the socket. If the breakdown is related to the wiring, it will not be difficult to fix it.
It is necessary to check the voltage on individual cores, find the faulty wire and replace it. Here, as well as when working with other types of switches, it makes sense to clean the oxidation at the contacts, if any.
Reassembling is not difficult: connect the main unit to the power supply, install it in the socket and fix it there with screws, then attach the panel with sensors and a decorative plate.
The protective mechanisms of such switches respond to breakdowns by interrupting the power supply. Even if the bulb just blows out, the switch goes into the “off” position, which does not change, even if the bulb is already replaced.
In this case, after repair, you just need to touch the plate to turn on the light. If there are no other failures, the touch switch will work properly.
Repair Recommendations
Contact problems are easily resolved. First they need to be examined. If they have a layer of oxidized metal, it should be removed, and then establish contacts in place.
If the contacts are not just oxidized, but have pronounced signs of fusion, usually they cannot be repaired, the device will have to be completely replaced. It is very simple to remove carbon deposits from the contacts, for this you can use a knife or the end of a flat screwdriver.
Visual inspection of the wires both in the socket box and in the junction box will help to identify and eliminate the cause of the breakdown. Repair damaged items or replace them completely.
When working with wires, you need to pay attention not only to the condition of the bare ends, but also to the quality of the wires themselves. For example, fragile veins can easily break, break, etc. In this case, part of the wiring will have to be replaced.
Among the common causes of weakening and disturbance of contacts are:
- increased humidity, which stimulates oxidative processes;
- Incorrect, for example, too weak wire fastening;
- excessive load, as evidenced by sparking, buzzing, crackling and other similar signs;
- mains voltage exceeding the permissible level;
- frequent voltage drops, etc.
To reduce problems with soot at the contacts of the switch, experts recommend the use of energy-saving lamps, rather than traditional incandescent lamps. The network load is reduced, and components wear out more slowly.
The process of disassembling and repairing a conventional two-key switch is presented in this video:
Here you can get acquainted with the device and the features of disassembling the touch switch:
This video shows the disassembly and device of the rotary switch:
Proper disassembly of the circuit breaker is an important step in the repair of the device. It is necessary to remember the safety measures, as well as carefully remember or photograph each stage of this process, so that the reassembly was also performed without problems.
Have experience disassembling the circuit breaker? Or want to ask questions on the topic? Please comment on the publication and participate in the discussions. The feedback block is located below.