It is difficult to overestimate the role of washers in everyday life. Units unfamiliar with fatigue diligently perform part of the routine duties for the owners. Unfortunately, their mechanisms are characterized by periodic failures. Therefore, it is better to figure out in advance how to drain the water from the washing machine, so that in the event of a breakdown, know what to do.
We will talk about how to empty the washing machine tank if the programmed duty cycle is not completed. In our article, we describe all acceptable methods that have been tested in practice. Our recommendations will help to properly prepare the equipment for recovery.
When does the need arise to drain the water?
Regardless of the brand of the washing machine, its technical complexity and type of load, the reasons for draining water from the working tank are absolutely identical. If you exaggerate the situation, you can describe it as an interrupted cycle that did not end with the programmed drainage of water through the drain hose to the sewer, or refusal to spin.
The reasons why the machine stops draining water are conditionally divided into the following groups:
- Blockages of internal nodes and channels. A case common enough for washing equipment due to the standard separation of fibers, loose stitches, decaying and "dusting" of the old fabric, the ingress of fine litter and foreign objects into the working bodies of the equipment.
- Blockage of the output channels. The reasons are similar to the above assumptions. However, in this case, the “traffic jams” that interfere with the water outlet are not related to the washing mechanism. They are confined to the outer drain hose and to the adjacent parts of the sewage system.
- Technical issues. This category includes an extensive list of minor irregularities and serious damage. Everything can happen, from the burnout of the winding of the pump to the drainage system to the manifestation of defects in the transmitting command of the device.
There is another reason that has nothing to do with blockages or breakdowns - this is our inattention. It is possible that the mode was simply chosen incorrectly. Suppose, because of forgetfulness, they did not switch the “gentle rinse” function after the previous session. If so, then just stop and restart the machine.
Image Gallery
Photo from
Problems with washing machines, forcing to resort to measures for the forced discharge of water, can accompany both an interrupted or a completed work cycle
If the machine has not completed the programmed work, soapy or almost clean water remains in the tank along with the laundry
The automatic washing machine will surely stop if powder intended for hand washing has been poured into the detergent drawer. In this case, the electronic control device may even be damaged by foam.
Often the machine interrupts work and operations if the drain hose is simply clogged or the entry point into the sewer through a siphon is clogged
Clogged filters and water-draining channels often happen if things with a pile are washed in equipment that is not designed to handle them, or if they do not use a mesh bag
A sudden stop of the washing machine occurs if, due to ill-treatment or wetting of the wiring, the electronic command device fails
One of the most common causes is a filter clogged with sediment, fibers and scale that protects the drain pump or breakdown of the pump itself.
It happens that the water from the tank is not discharged by the machine due to the incorrectly selected program. For example, after washing delicate things, the gentle rinse and spin mode was not switched
There is water left in the washing machine after washing
After completing the wash program, foam and water remain
Washer stopped due to increased foaming
Water stopped going from the washer to the sewer
Items with a pile are in the washing machine.
Cannot set program for washing machine
Drain pump filter clogged
Error codes on the display when selecting a program
A complex technical violation is not worth fighting with your own hands. Moreover, certified service centers that oversee products of certain brands often after independent intervention generally refuse to carry out repairs.
However, before deciding to disassemble the machine, you need to find out if the clogged hose or sewer siphon was the reason for the refusal.
Simultaneously with the drainage of water from the washing tub, the typical causes of blockages are eliminated, the filters and drainage channels of the washing machines are cleaned
It often happens that identifying the causes of failure of washing equipment to drain water in normal mode is accompanied by its simultaneous elimination. It is clear that this happens when the standard blockage is removed.
Filter clogs located in front of the drain pump, and clogging of the nozzles installed next to the pump can be handled independently without resorting to the expensive services of repairmen.
Regardless of what the stopping of the washing machine is associated with without completing the water drain, the same methods are used to get rid of it (+)
Options for draining water from the machine
The need to drain the water from the washing tub arises both for the machines that completed the programmed work and for those who interrupted the cycle due to a breakdown.
Procedure for locking the door
If not all the stages laid down by the control unit have been completed, then the hatches of the front models will still be blocked for 5 to 10 minutes. No need to pull the hatch holder and in vain panic. It will easily open after a period agreed upon by the manufacturer of the unit.
If, nevertheless, the hatch does not open after the time agreed by the manufacturer, then proceed as described in the instructions recommended by us. We advise you to read a very useful article, which describes the process in detail.
Better ahead of time to cover the floor around the machine with old bedding, towels or similar hygroscopic things, perfectly and quickly absorb water, and also able to hold it for a long time. In case of jamming, emergency unlocking tools are used.
If the visually determined level in the tank of the washing machine leaves no doubt that the floor in the room will be fairly flooded, do not try to open the hatch immediately after stopping
If after opening the hatch in the drum there is water that can be scooped out with a plastic bucket or a measuring cup, it is wiser to do just that. Having got rid of part of the water in this way, we ourselves will greatly simplify the task.
Almost all of the water can be scooped out of the top loading washers, then the residues can be drained through a hose. The front aggregates approach is somewhat different. You can easily draw water from the drum if it is relatively small in it, i.e. the level does not reach the upper edge of the lower edge of the rubber cuff.
Image Gallery
Photo from
Bucket for collecting water from a vertical model of the washer
Vertical Washing Drain Hose
Draining the washing tub into a bucket
Drain the collected water from the machine into the sewer
If there is clearly more water in the front technology than would be desirable for safe scooping, it is better not to risk it and not open the hatch right away.
It is advisable, without opening the frontal machine, to slightly move it away from the rear wall. Then you need to slightly “tilt” it back and carefully lean it against the wall with the top edge. From such a movement, water-containing containers will be shed on the floor much less.
If there is a chance of water spillage when opening the hatch of the front model of the washing machine, it is better to push it slightly “towards you” and carefully lean it against the wall with the upper edge of the body
It is important to remember that all actions with the washing machine, regardless of their degree of complexity, must be performed by turning off the equipment and removing the plug from the outlet. It is also necessary to shut off the supply of tap water. Next, we will analyze the options for draining the water from the washing tank.
Method # 1 - Using the Emergency Hose
The possibility of the described situations is provided by a number of manufacturers. For example, in the Samsung line of washers and Bosch appliances there are models with an emergency hose located next to the washer filter, through which the tank filled with water is easily and simply emptied if necessary.
This device is located next to the drain system filter. To access it, just open the decorative hatch located at the bottom of the front panel of the machine. It disguises and protects the nodes necessary for servicing.
Image Gallery
Photo from
Cover for the service area of the washing machine
Conclusion of an emergency hose in capacity
Drain water through the emergency hose
Hose in the service compartment of the washing machine
To discharge:
- We remove the emergency hose from the nicheintended for its laying in an idle state.
- Install a flat container directly under the hatch or as close as possible to him.
- Remove the cap from the edge of the hose, put it in a container and wait until all the water from the washing tub is completely merged.
If this hose also clogs during the draining period, it is better to clean it carefully immediately, without disconnecting it from the machine.
One of the options for the emergency discharge device does not imply a hose at all. The water from the washer in these models is drained through a plastic channel
Method # 2 - drain through the filter hole
This method, of course, refers to the most time-consuming and "dirty." The drain hole to which the drainage hose is attached is located behind the decorative hatch described in the previous case. A filter is installed in front of the hose inside the structure, which, according to the rules of operation, needs to be cleaned periodically.
In older models of washers, for example, in Indesit brand models, the drain hole with the filter inserted above it is quite low, and it’s quite difficult to substitute even an almost flat container under it.
Image Gallery
Photo from
Option for service cover over the entire width of the machine
Protection against water leakage from the drain system
Decorative hatch on the right side of the body
A plate with low sides, but since it will fill up extremely quickly, the hole will often have to be blocked, tightly twisting the device with a filter grill. Then open again and close again - this is a long time, but the drain is carried out fully and efficiently.
The filter drain algorithm is as follows:
- Open the service cover - a small hatch located at the bottom of the machine.
- Carefully unscrew the plastic fixture with filter grill, setting it in motion counterclockwise with an existing screw. First, unscrew quite a bit, about 10 °. If it does not give in, then we will help him with a screwdriver inserted into the groove on the screw.
- Drain the water. By loosening the tight connection in the area of the drain unit with the filter, we achieve a stream that is convenient for collecting water. Filling the stored plate or cuvette, we screw the filter screw back so that the water does not flow.
So we act until the machine is completely free of water. Having completed the drain, we remove the device with a filter grate and clean it.
Water is removed in portions through a drain system filter. Having slightly unscrewed the filter, gain capacity, twist the filter back. After emptying the container, everything is repeated until the water is completely removed
By the way, it is not the cleaned filter that is a characteristic reason for the machine to stop without completing the operations set by the task. With frequent repetition, this leads to an excess load on the drain pump and to its almost inevitable failure.
Image Gallery
Photo from
All washing machines require periodic cleaning of the filter from sediment. Regular maintenance protects the drain pump from breakage. In order to prevent the drained water from spilling onto the floor, it is better to move the washing machine slightly away from the wall and tilt it back slightly, as if pushing the rear edge of the top panel to the wall
Before removing the filter of the drainage system for cleaning, the floor is covered with absorbent laundry prepared for washing
We stock up on a container for collecting water. It is desirable that it be flat, with low sides
Open the service cover, behind which is the screw handle of the drain filter
We unscrew the filter by turning it counterclockwise. If it is tightly twisted due to jammed or dirty threads, apply force to the handle with a screwdriver
Carefully remove the filter, remember its location before removing. Insert it back on the same side.
We wash the filter under running tap water, completely clean it and carefully wipe it before reinstalling
Having completed the cleaning of the filter, we install it in the slot, just driving it into the grooves designed to fix it. We wipe the floor, wash the items used in the work and prepare for the upcoming washing
The washing machine is in the bathroom
Towel next to the washer
Suitable container for collecting drained water
The drain filter is removed
Dirty filter removed from the washer
Filter cleaning
Cleaning after cleaning the washing machine
Method # 3 - Using a drain hose
This is the easiest and most efficient way to free the washing tub from water. True, it is suitable if the filter of the drainage system and the drainage hose itself are not clogged. Most often, you have to do this if the pump breaks, pushing water into the sewer.
According to the described technique, the drain hose attached to the rear panel of the unit must be unscrewed from the hole intended for it and simply laid on the floor previously covered with rags, arrange at the lowest level.
To remove water from the machine with a drain hose, it is detached, laid on the floor. As soon as water flows from the hose, it is led into a bucket and the washing tub is empty
If water comes out of the hose, immediately put it in a container nearby. Everything that spilled by should be cleaned immediately, without waiting for the arrival of indignant neighbors from the apartment below you. After the machine is free of water, it is necessary to clean the drain hose filter and screw it back to the hole on the back of the device.
Before you start unscrewing the hoses for draining the water, you need to study the instructions and understand whether it is possible to drain the water at all according to the technology shown in the example
Note that the method described in this example is not suitable for all machines. For a number of modifications from Siemens and from Bosch, a part of the drain channel is arranged in the form of a loop located inside the housing.
Thanks to the indicated constructive solution, spontaneous discharge of water does not occur during operation, but it is also impossible to empty the tank using the described method.
In order not to waste time, it is better to look in advance at the passport and technical documentation attached to home appliances. If the indicated design feature has a place to be, you must choose another method for draining.
After removing water from the machine, it is recommended that the filters located at the connection points of the drain and supply hoses be routinely cleaned.
Method # 4 - discharge through a drain pipe
In the execution of the forced version of the drain through the pipe, radical measures will be required to disassemble the machine.
To resort to this method without obvious reasons is not worth it. It is suitable if all of the above methods did not end with the expected result. Moreover, its implementation requires the application of male hands.
How to determine what the washing machine needs to be disassembled? A typical sign is the complete absence of water in the drain hole after removing a filtering device with a mesh from it. This means that the inner channel is blocked, which diverts water to the drain hole.
If it is impossible to discharge the water using the above methods, resort to radical measures - cleaning the drain pump nozzle
The sequence of actions in the event of a drain through the pipe:
- Remove the back or front panel of the washerhaving previously unscrewed the fasteners and laid it in a suitable box or plastic cup.
- We find a drain pipe. It is located under the tank, inside which the drum rotates.
- Substitute any flat capacity under the site under the pipe, the area around is covered with rags for instant collection of spilled water.
- We disconnect a collar, by which the pipe is connected to the pump of the drainage system, dismantle the pipe, after which water should flood. We quickly collect it and pour it into the sewer.
- We clean the nozzle and the adjacent channel is just a finger, a pencil or a similar object.
Having finished draining and cleaning the nozzle, we install the machine parts in their proper place, we twist them with effort, not forgetting that everything should be tightly connected to the maximum.
Before cleaning the nozzle, it is necessary to disconnect the front panel of the housing and check the condition of the drainage system. It is possible that some parts and assemblies need not only to be cleaned, but also to be replaced
If during the cleaning work it is found that the drain pump is clogged with litter and fibers, carefully unscrew the pump cover and clean it of any impurities that interfere with the work.
At the same time, we clean the thread of the drain pump and the inner surface of the housing. Check how the impeller rotates. If it’s free, we assemble the system in the reverse order, if rotation is difficult, we clean the connection unit of the impeller with the motor of the device.
When disassembled, it is easier and more convenient to clean the drain system. If necessary, the pump can be detached and completely cleaned of deposits and contaminants.
Recommendations to hostesses and home masters
An impressive list of breakdowns and machine stops without completing the program can be elementarily prevented by observing the simplest operating rules:
- Remove all contents from pockets before loading items into the drum.. Coins, paper clips, earrings, rings, small luggage keys and similar metal objects are especially harmful to the unit.
- Check the strength of sewing on buttons and zippers. Before immersing clothes prepared for washing, locks-snakes and buttons must be fastened.
- Brush dust and sand under the lapels and pockets with a brush..
- Remove hooks before washing curtainsby means of which they are connected to the cornice wheels.
Do not forget that the washing unit is a complex technical device that requires a careful attitude.
It will be useful to put thin linen and things with a pile into mesh bags, which are specialized in washing machines. Instead, it is permissible to use a thin cloth or a bag independently sewn from it
We regularly clean the drain system filter at the intervals specified by the manufacturer.
If we load worn linen in order, clean the filter after each wash.
Video # 1. Draining water using an emergency hose and primitive filter cleaning:
Video # 2. Demonstration of the process of removing water from the washing tank of the activator machine:
Video # 3. Details on the technology of draining water from the machine:
Strict observance of operating rules in most cases avoids situations requiring forced draining of the water tank. However, no one is completely safe from them..
Therefore, it is better to get information in advance about all the possible methods used by independent home masters.
Want to talk about how the water was drained from the washer tank after a malfunction? Do you have useful information on the topic of the article, is there a desire to share only with you a known method? Please write comments in the block below, ask questions and post photos.